MESR-100 V2 ESR Capacitance Ohm Meter test Capacitor meter with SMD Clip Probe

Description

Product Description
MESR-100 V2 ESR Capacitance Ohm Meter test Capacitor meter with SMD Clip Probe
Features:
JINGYAN MESR-100 V2 Auto-ranging capacitor ESR and Low Ohm Meter
Measuring range from 0.001 to 100.0R, support IN CIRCUIT Testing.
Using true 100 KHz sine wave to measure the ESR value, which is equal to the testing method of capacitor manufacturer.
In the market, there is some technique using short pulse method to testing, but the value will be varying vs the capacitance and sometimes reading is different from the manufacturer's value.
What is ESR of capacitor?
There is a series resistor inside capacitor, using 100kHz to remove the impedance 1/(2*pi*F*C), the impedance become small, and we can then measure the true series resistor value.
A bad E-capacitor will have larger ESR and create large ripple rather than filtering noise. Normally, a big capacitor is larger than 3 ohm.
Using this theory, we can measure the capacitor is bad/ damaged or good in condition.
Because our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a result we can use it as in circuit test. Because this low testing voltage, it cannot turn on the semiconductor inside a circuit under testing.
During repairing TV, LCD, Audio board, etc. we can in circuit testing the capacitor is good or not.
*Dual terminal, for fast and easy inspect general capacitor or resistor, a printed ESR table for fast check
Compare MESR100 old V1 and new V2 Improvement:
1)
Change square wave to sine wave 100 KHz, reduce square wave’s high frequency component, and affect the reading passing the test leads and capacitor.
2)
Higher Resolution up to 0.001 ohm.
3)
128X64 dot matrix LCD, with more larger value display and information
4)
Embedded 25V capacitor table at LCD, auto display the capacitor is good or bad reference to common 25V electrolytic capacitor.
5)
New plastic case, curve design for hand carrying. New stand for 60 degree stand on desk.
6)
Use 2X AA battery, more convenience and longer battery life than 9V battery.
7)
Support external USB power, using standard micro-USB port.
Specification:
Range
Accuracy (After Zero, tested with 1,10,100R resistor)
Refresh Time  (Manual Mode)
*Auto mode take  0 to 2s more time depend on value
0.000 to 1.000R
1%+2Digit
~0.4s
1.000 to 10.00R
1%+1Digit
~0.4s
10.00 to 100.0R
2%+1Digit
~0.4s
*Accuracy maybe affected by the test lead’s length and contact point resistance.
Standard test leads is 15cm, for longer test leads need special shielding to affect the EMI inference (Can contact sales’ person for more detail)
1)
Accuracy:  Up to 1% (detail on above table)
Wide Measurement Range:  >1uF (for 0.1uF the error will be larger on equation 1/(2*pi*F*C) @ 100Khz )
2)
High Resolution: 4 digit, or 0.001Ohm @ 1 Ohm range
3)
Measuring voltage: <~40mV RMS (TESTING VOLTAGE)
4)
Clamping voltage: ~0.15V (open voltage)
5)
Battery 2X AA 1.5V battery
6)
External Power: 5V micro USB
7)
Operating current 0.02A
8)
Battery Life time: >80 Hours
Operating Introduction:
1)
POWER ON
Press and hold the ON/ OFF circle orange button for 2 to 3 second to power on.
Press and release the ON/ OFF button to shut down meter.
2) AUTO/ MANUAL mode:
i) Auto Range:
Press and release the RANGE button and at the first line of LCD will show “AUTO:"
At auto mode meter will automatically select the best range to detect.
ii) Manual Range:
Scroll the manual range from 1R, 10R and 100R range by press and release the RANGE button
In LCD will show MANUAL at first LCD line and show at second line: 0-1R, 1-10R and 10-100R.
3) 1 Key Zero:
Short circuit the test leads’ terminal, cancelling the wire resistance.
Press and release the “ZERO" button, LCD shows “ZERO" and wait the zero disappear.
If you are using the meter array socket, you need to use a short pin to short circuit to set zero.
4) Backlight:
LCD backlight will on during power on
5) Auto Sleep:
Around 10 hours for not testing, it will shut down automatically to save power.
6) OVERFLOW or OL:
Display overflow when the value is out of range, you can check that you are zero correctly.
7) ESR TABLE:
It is for reference only, different manufacturer of capacitor has different ESR, better to test a good cap ESR and compare with what you are testing, usually bad cap with higher ESR few times larger than good one.
8) SOFTWARE ESR:
Put the 25V Electrolytic capacitor value to LCD, and compare,
GOOD if C < XXuF, means the capacitor maybe good condition if it is less than XXuF
9) PLASTIC STAND:
If you don’t use the stand, press and push the lock position
Package include:
1  * MESR-100 V2 meter
(batteries not included)
2 *
test probes
1 *PCS SMD clip probe
About Us
We are aiming to bring the best products  as well as service to all of the customers . If you have any needs, please don't hesitate to contact us at any time .
Payment
We accept PayPal only.
All PayPal payments must be confirmed (shipping and billing addresses must match).
Payment must be received within 7 business days of auction closing.
We ship to your eBay or Paypal address. Please make sure your eBay and  Paypal address is the same and correct before you pay.thanks.
Shipping
1,We ship items to your PayPal confirmed address only. Please make sure your  address in PayPal is matched with your shipping address on ebay before you pay.
2,We are unable to take any responsibility for wrong address, any custom delay  or tax. Because transit time is highly depended and provided by Postal Service.
3.Items will be shipped within the handling time as we promised.
4.The ETA Delivery time depends on destination and other factors.(public holidays., natural disasters, customs issue and other unexpected impact, etc)
Import duties, taxes, and charges are not included in the item price and shipping cost. These charges are the buyer's responsibility.
Please check with your country's customs office to determine what these additional costs will be before prior to bidding or buying.
If you have any request or question about our handling and shipping, please feel free to contact us via eBay message.
In a word, we will do our best to serve you.
Returns
If you are unsatisfied with the items received ,please contact us (via eBay Message) first before you operate the return or leave feedback .
We must go to the extreme length to solve all of the issues  in the first time.
If you have not received your products within 30 days from payment, please contact us. We
will track the shipment and get back to you asap. Our goal is
customer satisfaction!
powered by